DISOMAT TERSUS MANUAL PDF

DISOMAT TERSUS MANUAL PDF

The compact DISOMAT® Tersus weighing terminal is ideal for use in a wide range of weighing applications, regardless of whether you’re focusing on operating. DISOMAT® Tersus to control a crane DISOMAT® Tersus panel-mounting unit in field housing DISOMAT® Tersus Crane Scale, see Manual BV-HAA. A Schenck model DISOMAT Tersus (VTG ) digital indicator as shown in between weighing ranges may be automatic or manual.

Author: Zulujas Dutaur
Country: Equatorial Guinea
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 24 November 2011
Pages: 162
PDF File Size: 15.85 Mb
ePub File Size: 5.73 Mb
ISBN: 262-8-56115-708-9
Downloads: 64796
Price: Free* [*Free Regsitration Required]
Uploader: Zunos

If bus boards are equipped with jumpers for configuration, set these before mounting accessiblity.

DISOMAT® Tersus

Width [mm] 73 10 6 24 40 30 Maual [mm] 99 99 35 48 48 90 78? Every single data record includes the following values: Bolts can then be tightened easily with the use of a hex socket head spanner. They can also adversely affect weighing operation. All fieldbus interfaces are designed as cards to be plugged into the processor card. The total number of digital and analogue inputs and outputs has been doubled.

For wiring diagram, see page 46ff. Any reproduction of this documentation, dissomat of method, without prior permission by Schenck Process GmbH in writing, even by excerpt, is prohibited.

DISOMAT® Tersus

Dongle With Jumper Settings To parameterize and calibrate your system: Set baud rate and station address of the device in the dialog mode. Safety Instructions Use As Originally Intended The measuring system and its connected mechanical components are exclusively designed for weighing and controlling tasks.

Related Articles  AGILE JAVA JEFF LANGR PDF

Perform parameterization and calibration as described in the Operating manual. Best use new hex maanual from the bus board kit in place of the recessed head screws.

The entire signal chain is designed so that the device identifies logical HIGH if switch is activated, and logical LOW in case of wire breakage. Secondary Displays You can connect various secondary displays for different mounting sites e. Real time clock RTCmin. They are of rugged and standard industrial design.

Fitting D is provided for fieldbus connectors. When connecting load cell cable, ensure good contact of cable screen using the clamps supplied. Explosion-proof Protective Circuitries The explosion-proof protective circuitry consists of plug-in Z barriers placed on a carrier module equipped with 6 slots. Linearity Zero point stability Range stability? Operate your device in proper condition and as orginally intended.

Base Tdrsus Figure 4: Remove clamping nut and press in plug flush with the screwed connection outer edge. The device is equipped with corresponding type plate. Insert the three spacers into the processor board.

Connect and supply the DT control terminal in the safe area as shown in wiring diagram on page The module is organized as ring buffer, i. This means that the operation from the PC keyboard is exactly the same as on the device direct.

Related Articles  BCIS ALTERATIONS AND REFURBISHMENT PRICE BOOK PDF

This type is a variant of stainless steel unit Mmanual adjusted to explosion protection requirements.

Assemble parts of the dongle plastic housing using clips. To ensure optimal EMC resistance, we recommend to use the cables indicated for the single fieldbuses. With the further use of our web pages, you agree to the use of cookies. Fieldbox VFG 4. The version with two measuring channels increases efficiency by making parallel measuring and feeding possible on both channels. Open device and dongle housing from the side using a screw driver.

System Manual DISOMAT_百度文库

Parameters incorrectly set may cause injuries or damage to the machine whenever a user control system is connected. However, danger can arise from transit of material to be weighed e. B01 mmor V To ensure the high degree of protection: The ICP relay outputs can be loaded with max.

The table below lists the available variants: Installing Fieldbus Interface Fig. To replace, remove barrier from carrier module. In operation with two measuring channels: E unit is at least 12V.

In addition, the load cells signals can be recorded individually.